Company details for:

Condair Limited

Submit press release

(4)

Artex Avenue,
Rustington,
Littlehampton,
West Sussex,
BN16 3LN,
United Kingdom

Quick Links:

Products

Condair EL Electrode Boiler Steam Humidifier

The Condair EL electrode boiler steam humidifier provides reliable steam humidification and is easy to install, use and service. It can be used with steam lances to humidify an air handling unit or duct, or with a fan unit to directly humidify a room.
The steam cylinders of the Condair EL last up to three times longer than similar models due to advanced water quality management. The mineral content of the water is precisely monitored and managed. Water with high mineral content is drained and fresh water added only as required, thus minimising scale build-up and reducing the energy needed to heat fresh water.

Condair RS Resistive Steam Humidifier

This electric steam humidifier delivers accurate humidity control without the expense of plastic disposable boiling cylinders and simplifies maintenance with its patented scale management system.
Scale that forms on the heating elements breaks off under normal operation and falls into the externally located scale collector tank. Scale removal is a simple process of draining the scale collector tank with the push of a button, allowing the unit to cool then disconnecting the tank and emptying it.
The Condair RS can operate with mains water to provide ±3%RH control or on reverse osmosis (RO) water to offer ±1%RH control. When operating on RO water, scale build-up is virtually eliminated, significantly reducing the unit's required maintenance.

Condair GS Gas-Fired Steam Humidifier

The Condair GS offers high capacity steam humidification with low operating costs. The economy of using gas makes this humidifier around 60% cheaper to power than an equivalent electric steam humidifier. This can provide a fast payback when replacing electric steam, especially on high capacity systems.
This gas-fired humidifier incorporates a 360° flame encircling the burner, which provides a high thermal efficiency of over 90%. This results in a faster response to humidification requirements, closer humidity control and minimal gas consumption.
The Condair GS has been designed to incorporate large flat heat exchangers that shed their limescale during operation, helping to reduce maintenance and maintain efficient heat transfer.

Condair ESCO Live Steam Humidifier

The Condair ESCO uses steam from a building’s existing steam network to provide humidification to an air handling unit (AHU) or duct. It conditions the steam to remove condensation and ensures that only dry steam is delivered for humidity control.
It can operate at up to 4bar and provide up to 2,000kg/hr of humidification to an AHU. It incorporates a ceramic rotary disc valve that offers 0-100% modulation, very close control and prevents the possibility of steam leakage when closed.
The Condair ESCO’s patented steam lance has tiny inner nozzles that draw steam only from the centre of the steam lance, where it is at its hottest and driest. This ensures that any condensation that occurs around the cooler outer edges is not introduced to the duct.
Unlike other live steam humidifiers that incorporate pre-heated steam lances to avoid this “spitting”, the ESCO’s steam lance reduces heat transfer to the air stream and provides instant humidity on demand without any pre-heating time needed.
The Condair ESCO is available in cast iron or stainless steel models with a variety of steam pipe options to suit duct dimensions and satisfy required absorption distances.

Condair LS Live Steam Humidifier

Condair LS live steam humidifiers are designed to control and distribute steam under pressure from a central steam boiler for direct introduction into a duct or AHU.

Condair LS steam lances are constructed of high quality 304 stainless steel and are available in single or multiple configurations. There is a wide variety of lengths ranging from 12" to 144" to suit any duct size and give the best possible steam dispersion.
The steam lance is pre-heated with a 97% jacketed exterior. When steam is first introduced to the humidifier it flows around this outer jacket. This heats the inner lance so that when steam is introduced into it, the walls of the lance are hot and therefore condensation is prevented. This ensures only hot, dry steam is released into the duct without any "spitting".
An optional stainless steel insulation jacket encompasses 1/2" fiberglass insulation to improve efficiency and minimize heat transfer to the air stream.

Condair SE Steam-to-Steam Humidifier

The Condair SE humidifier provides sterile steam for in-duct humidification from impure, raw boiler steam.
The raw steam passe through a stainless steel heat exchanger, providing the heat to produce clean steam that is distributed to the air handling unit or duct.
The Condair SE is available in a variety of outputs with models ranging from 23 to 477kg/hr.
It is ideal for use in buildings with a central boiler system, like hospitals or large institutions.
The heat exchanger has been designed with large flat surfaces to make maintenance easy when removing scale.
An outdoor model with weather-proof enclosure is available.

Condair CP3 Mini Low Capacity Steam Humidifier

The Condair CP3 Mini will provide up to 4kg/hr of steam either directly to a room or into an air handling unit. It has a very attractive yet inconspicuous design with concealed rear connections for power and water.
This low capacity steam humidifier can be serviced without needing to call a technician. All electronics and current carrying parts are protected against water splashes and inadvertent contact allowing cylinders to be changed safely.
A large LCD display provides information on all operating parameters and the unit can be controlled with the integrated keypad. An optional battery-powered humidity sensor can be located in the room and transmits a signal back to the humidifier to control output to the desired level.
The Condair CP3 Mini operates on mains water and is ideal for both homes and offices.

Condair ME Evaporative Humidifier & Cooler

The Condair ME provides low energy humidity control and evaporative cooling to an air handling unit or duct.
A single unit can provide up to 1,200kg/hr of humidification and 822kW of evaporative cooling to an air stream while operating on less than 1kW of electricity. As well as being economic to run the Condair ME is also easy to operate with an advanced touch screen control panel, simple to maintain with industry leading service features and employs the latest in hygiene technology.
The self-contained hydraulic unit supplies water to the top of the evaporative module, located either inside or outside the duct. Exterior mounting enables most servicing to be carried out without having to shut down and enter the air handling unit.
The Condair ME incorporates up to seven low energy 32W pumps rather than single large pump. This allows proportional energy consumption to system output and provides up to seven-stage control as standard.

Condair DL Hybrid Spray & Evaporative Humidifier

The Condair DL combines spray and evaporative technologies to provide close control, hygienic in-duct adiabatic humidification with low operating costs.
A grid of nozzles releases a fine spray into the air stream towards a ceramic droplet evaporator. What moisture isn't immediately absorbed by the air precipitates onto this ceramic evaporator. As air flows through its porous surface, more water is absorbed by the air for highly efficient water use and droplet-free humidification.
This efficiency enables the humidifier to provide very close control at up to +/-2%RH, which is a level of control usually only achievable with steam humidification.

Condair HP High Pressure In-Duct Humidifier

The Condair HP delivers adiabatic humidification and cooling to an air handling unit (AHU) or duct. A series of nozzles mounted across the air stream atomise water under high pressure creating a fine mist that is rapidly absorbed. A droplet separator downstream removes any un-evaporated moisture from the air ensuring droplet-free humidification.

The nozzle lines are connected to a high pressure pump station and a water treatment system. Minerals are removed from the supply water before it is provided to the nozzle lines at between 60-70bar. A single pump station is capable of supplying nozzle lines in multiple AHUs with up to 1,300kg/hr of moisture. The system has a high humidification capacity and offers up to 884kW of adiabatic cooling from just 2.2kW of consumed electricity.

JetSpray Compressed Air & Water Spray Humidifier

The JetSpray provides very accurate humidity control directly to a room's atmosphere using a combination of compressed air and water. A series of strategically located nozzles provide consistent humidity throughout the space.
The use of compressed air ensures very rapid moisture evaporation, without the risk of wetting or drips, and highly directional spray aerosols.
The JetSpray is available in 60L/h and 600L/h capacity models. The 600L/h model is available with on/off control or fully modulating 0-100% output for highly accurate +/-2%RH humidity control.

Draabe NanoFog Evolution High Pressure In-Room Humidifier

This quiet and discrete in-room spray humidifier is ideal for commercial buildings that do not have central air handling units. The nozzles are barely audible, just 10cm high and each can deliver up to 3kg/hr of humidification directly to a room with rapid evaporation.

Multiple nozzles can be combined and controlled from a central panel to deliver up to 200kg/hr with zone control allowing humidity levels to be controlled independently in different rooms.

The system consists of a reverse osmosis (RO) water treatment system that removes the minerals from the supply water, a high pressure pump, the in-room nozzles, hygrostats and a central control panel.

ML Princess High Pressure Direct Air Humidifier

The ML Princess is a ceiling mounted humidifier delivering between 12-54l/h per distribution unit. It is ideal for use in production areas and doesn't require a compressed air supply.

An integrated fan draws air from below and distributes the moisture particles for rapid evaporation in the atmosphere and uniform humidification in a room.
The system has very low energy consumption with a single distribution unit providing up to 54kg/h while operating on just 120W.

ML Solo High Pressure Direct Air Humidifier

The ML Solo high pressure humidifier provides low energy humidity control and evaporative cooling directly to a room's atmosphere.

A series of spray units are strategically located in the area being humidified and are connected to a high pressure pump and water treatment system. Supply water is filtered to remove any minerals and then supplied to the spray units at between 50-70bar. When released through the high pressure nozzles, the water atomises and is absorbed by the air.

The nozzles can be suspended from a ceiling or mounted on a wall. Adjustable joints allow their sprays to be directed. A fan unit under the nozzles encourages evaporation and assist in directional control.
Each spray unit can provide between 1.5-5 litres per hour and are available in white, grey or black.

ML Flex High Pressure Direct Air Humidifier

The ML Flex is a high pressure spray humidifier for use in industrial manufacturing, horticulture, dust suppression and evaporative cooling.

A series of high pressure nozzles are located on a custom made line for each application and are connected to a high pressure pump station and water treatment system. Minerals are removed from the supply water and delivered to the nozzles at between 60-70bar. On release the water atomises and is absorbed by the air raising its humidity.

Defensor PH15 Mobile Humidifier

The Defensor PH15 mobile humidifier can deliver up to 1.7L/hr of humidity to a room while operating on just 72W of electricity. It is ideal for use in offices, humidors, museums, galleries or any single room up to 580m³.

The system has a circular evaporator mat that rotates through a water reservoir. A fan draws in dry air through the grilles in the sides of the unit and through the moist evaporator mat. The air absorbs moisture before released through vents in the top of the unit optimally humidified.

Condair PureHum 1000 Pro Mobile Humidifier

This commercial mobile humidifier is ideal for areas up to 1,000m³ with a maximum output of 2.6L/h. It has a large 50 litre water tank or can be directly plumbed-in to a mains water supply for continuous operation.

Alongside humidification, this unit offers air purification with a fine dust, F7 filter, HEPA H10 and activated carbon filters available.

The unit has a programmable timer to control operation, and a clear touchscreen interface, which displays settings and current room temperature and humidity. Control can be PIN protected to prevent unauthorised access, or controlled remotely via a phone app with its integrated WLAN/wifi module.

Made from high quality UV-resistant plastic and stainless steel, the Purehum 1000 Pro offers robust performance and will not discolour in sunlight.

A UV lamp inside the water tank combats bacterial growth for hygienic operation. When connected to a mains water supply and drain, a flushing feature will automatically cycle water through the unit to ensure water cannot stagnate in the system, further enhancing hygienic operation.

Condair OptiSorp Short Evaporation Steam Distribution Manifold

The OptiSorp steam distribution manifold shortens the evaporation distance of steam released inside a duct or air handling unit (AHU). This prevents steam from coming into contact with components or corners within the AHU and ensures reliable and hygienic steam humidification.
Tiny patented inner nozzles on the manifold draw steam from the centre of the steam pipe where it is at its hottest and driest. This guarantees that steam is introduced to the AHU without “spitting” that can occur when condensation forms around the cooler outer surface of the pipe.
A uniform spread of these nozzled outlets across the whole manifold provides a consistent release of dry steam across the air stream and reduces the evaporation distance compared to standard steam pipes.
The OptiSorp is made of robust stainless steel for a long operational life.

Condair RO-A Reverse Osmosis Water Filter for Humidifiers

Reverse osmosis (RO) is an effective and economic way of removing minerals from water. The Condair RO-A has been developed specifically to provide operational, energy and maintenance benefits to Condair humidifiers.
By removing the minerals from a humidifier’s supply water, the limescale that builds-up in the system is virtually eliminated. This results in a much lower level of required maintenance in all types of humidifier and reduced energy consumption in steam humidifiers. These cost savings can lead to a payback on the initial purchase of the Condair RO-A unit in around one year.

Condair DA Desiccant Dehumidifiers

Desiccant dehumidifiers are ideal for providing dehumidification at very low temperatures or when very low humidity levels are needed. The Condair DA range can operate effectively down to -30°C and maintain an atmosphere as low as 10%RH.
A range of additional modules can be connected to the dehumidifier, providing flexible operation, enabling it to deliver air exactly as an application requires it. These include pre- or post-cooling batteries, heat exchangers and condensation modules.
The additional heat exchangers can utilise gas, hot water or steam to reduce the operating costs of the system and can be operated alongside the regular electric heater. Models up to 20kg/h have electrical reactivation with advanced self-regulating PTC heating.

Condair DC Condensing Dehumidifiers

Condensing dehumidifiers are ideal for lowering humidity levels to around 50%RH and at temperatures above 15°C.
The Condair DC range offers capacities from 75-930 litres per day and air flows from 800 to 8,500m³/h, making the dehumidifiers ideal for drying complete buildings. The systems can deliver dry air directly to a room's atmosphere or be connected to a building's ventilation system.
All models come with a hot-gas defrost feature as standard and only use highly efficient R410A refrigerant gas.

Condair DC Wall & Ceiling Mounted Condensing Dehumidifiers

This range of condensing dehumidifiers offers powerful drying performance and the convenience of wall or ceiling mounting.
All models in the range incorporate R410A refrigerant gas and are made from hot-galvanised thick sheet metal with polyurethane powder enamel.
Each series comprises of five models with capacities ranging from 49 to 190 litres per day.
The wall-mounted versions can be supplied with optional steel feet for extra stability. Remote control wall controllers can be located up to 50m away and replicate all control functions. Wall-mounted remote mechanical hygrostats are also available.

Condair DC-N Condensing Dehumidifier with Cooling

This range of Condair DC condensing dehumidifiers can provide air drying and optional cooling with the use of an external compressor.
The unit can be operated in dehumidification-only mode, when waste heat from the dehumidification process is released into the room, or in cooling mode, when the unit dehumidifies and cools. In this second mode, the waste heat is ejected via the remote compressor.
Capacities range from 263 to 940 L/D (30°C/80%RH) and 13 to 43kW of cooling.
The housing is galvanised metal with a powder coated enamel as standard and available in stainless steel as an option.

Condair DC-LT Low Temperature Condensing Dehumidifier

The Condair DC-LT dehumidifier is effective at temperatures as low as 10°C. Regular condensing dehumidifiers are effective at temperature at above 15°C.
This range of dehumidifiers offers capacities from 260 to 940 litres per day and air flows from 3,500 to 8,500m³/h.
The housing is galvanised metal with a powder coated enamel as standard and available in stainless steel as an option.
Operation is controlled via its on-board digital display, an optional remotely located controller up to 50m away or via a BMS (Modbus).
The Condair DC dehumidifiers use energy efficient EC fans with a three speed selection.

Condair DP Swimming Pool Dehumidifiers

The Condair DP range of swimming pool dehumidifier offers a comprehensive choice for small to large commercial pools. All incorporate condensing technology and heat recovery systems to provide energy efficient operation.
In-room units are attractively designed and wall-mounted. They draw moist air in at the bottom and release dry air out of the top.
A similar range is available to be located in an adjacent room. Air is drawn from the pool area via ducting, dried by the dehumidifier and then supplied back to the room.
Ceiling mounted units can be located above a suspended ceiling system or left exposed if floor or wall space is not available in the pool or utility area.

About us

Condair Limited is the world’s leading manufacturer of commercial and industrial humidification and evaporative cooling products and systems, setting standards with regard to energy efficiency and hygienic solutions. We export to over 50 countries throughout the world. Our important own product brands are: Condair, Nortec, Defensor, Draabe and ML System.

Condair is represented in the UK by Condair Limited, which offers humidifier system advice, design, manufacture, supply, installation, commissioning, maintenance and spares from its base in Littlehampton, West Sussex. The company supports Condair sales activities in the UK, Ireland, Oceania, South East Asia and Central and Southern Africa.

From its production facility in West Sussex, Condair Limited manufactures the JetSpray compressed air and water spray humidifier, the Condair ME in-duct evaporative humidifier and cooler, and the PureFlo Reverse Osmosis water filter, all of which are distributed throughout the global Condair Group sales network.

Condair Limited is the new name for JS Humidifiers, following the company becoming a member of the Condair Group in 2011 and rebranding to Condair Limited in October 2014